Also Scheinbar wird, sobald der Stick beim Booten steckt keine DE Region geladen. Daher streikt das eingebaute WLAN. Im Luci ist überall DE eingestellt. Kann es sein, das der kmod-ath9k-htc einfach kein DE unterstützt und irgend eine Komponente nachlädt, die der eingebaute Atheros ebenfalls benutzt und entsprechend auch für diesen kein DE mehr möglich ist?
Im Luci sind folgende Module vorhanden - der htc wurde von mir nachinstalliert
Code: Alles auswählen
Paketname Version
Entfernen kmod-ath 3.18.10+2015-03-09-3
Entfernen kmod-ath9k 3.18.10+2015-03-09-3
Entfernen kmod-ath9k-common 3.18.10+2015-03-09-3
Entfernen kmod-ath9k-htc 3.18.10+2015-03-09-3
Entfernen kmod-nf-nathelper 3.18.10-1
Bootlog ohne Stick:
Code: Alles auswählen
root@Johannisviertel-Essbar:~# dmesg
Linux version 3.18.10 (mfuhrmeister@3dfx) (gcc version 4.9.2 (OpenWrt/Linaro GCC 4.9-2014.10 r44751) ) #2 Wed Apr 8 08:48:26 CEST 2015
MyLoader: sysp=9926862e, boardp=5f2bfe0e, parts=75c0efe4
bootconsole [early0] enabled
CPU0 revision is: 0001974c (MIPS 74Kc)
SoC: Atheros AR9341 rev 3
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone ranges:
Normal [mem 0x00000000-0x01ffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x01ffffff]
Initmem setup node 0 [mem 0x00000000-0x01ffffff]
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 803362b0, node_mem_map 81000000
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8192 pages, LIFO batch:0
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: board=TL-WR842N-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 28580K/32768K available (2562K kernel code, 128K rwdata, 308K rodata, 256K init, 194K bss, 4188K reserved)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:51
Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR842N/ND v2
Switched to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
futex hash table entries: 256 (order: -1, 3072 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 55
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
console [ttyS0] disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
console [ttyS0] enabled
bootconsole [early0] disabled
m25p80 spi0.0: found s25fl064k, expected m25p80
m25p80 spi0.0: s25fl064k (8192 Kbytes)
5 tp-link partitions found on MTD device spi0.0
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x00000012e650 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x00000012e650-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: device 2 (rootfs) set to be root filesystem
1 squashfs-split partitions found on MTD device rootfs
0x000000450000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
libphy: ag71xx_mdio: probed
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
ag71xx-mdio.1: Found an AR934X built-in switch
eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
TCP: cubic registered
NET: Registered protocol family 17
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 256K (80350000 - 80390000)
init: failed to symlink /tmp -> /var
init: Console is alive
init: - watchdog -
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ehci-platform ehci-platform: EHCI Host Controller
ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform: TX-TX IDP fix enabled
ehci-platform ehci-platform: irq 3, io mem 0x1b000000
ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
init: - preinit -
random: procd urandom read with 9 bits of entropy available
eth1: link up (1000Mbps/Full duplex)
jffs2: notice: (362) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found.
mount_root: switching to jffs2 overlay
eth1: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
NET: Registered protocol family 10
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip6_tables: (C) 2000-2006 Netfilter Core Team
batman_adv: B.A.T.M.A.N. advanced 2014.4.0 (compatibility version 15) loaded
u32 classifier
input device check on
Actions configured
Mirror/redirect action on
netem: version 1.3
Loading modules backported from Linux version master-2015-03-09-0-g141f155
Backport generated by backports.git backports-20150129-0-gdd4a670
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (450 buckets, 1800 max)
xt_time: kernel timezone is -0000
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
usbcore: registered new interface driver ath9k_htc
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
device eth1 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): br-batman: link is not ready
cfg80211: Calling CRDA for country: DE
cfg80211: Regulatory domain changed to country: DE
cfg80211: DFS Master region: ETSI
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
eth1: link up (1000Mbps/Full duplex)
br-lan: port 1(eth1) entered forwarding state
br-lan: port 1(eth1) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
eth0: link up (100Mbps/Full duplex)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
br-lan: port 1(eth1) entered forwarding state
IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
device wlan0-1 entered promiscuous mode
br-batman: port 1(wlan0-1) entered forwarding state
br-batman: port 1(wlan0-1) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): br-batman: link becomes ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: Created IBSS using preconfigured BSSID 02:ca:ff:ee:ba:be
wlan0: Creating new IBSS network, BSSID 02:ca:ff:ee:ba:be
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
batman_adv: bat0: Adding interface: wlan0.12
batman_adv: bat0: The MTU of interface wlan0.12 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
batman_adv: bat0: Interface activated: wlan0.12
8021q: adding VLAN 0 to HW filter on device bat0
device bat0 entered promiscuous mode
br-batman: port 2(bat0) entered forwarding state
br-batman: port 2(bat0) entered forwarding state
br-batman: port 1(wlan0-1) entered forwarding state
br-batman: port 2(bat0) entered forwarding state
random: nonblocking pool is initialized
root@Johannisviertel-Essbar:~#
Bootlog mit Stick
Code: Alles auswählen
root@Johannisviertel-Essbar:~# dmesg
Linux version 3.18.10 (mfuhrmeister@3dfx) (gcc version 4.9.2 (OpenWrt/Linaro GCC 4.9-2014.10 r44751) ) #2 Wed Apr 8 08:48:26 CEST 2015
MyLoader: sysp=9926862e, boardp=5f2bfe0e, parts=75c0efe4
bootconsole [early0] enabled
CPU0 revision is: 0001974c (MIPS 74Kc)
SoC: Atheros AR9341 rev 3
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone ranges:
Normal [mem 0x00000000-0x01ffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x01ffffff]
Initmem setup node 0 [mem 0x00000000-0x01ffffff]
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 803362b0, node_mem_map 81000000
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8192 pages, LIFO batch:0
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: board=TL-WR842N-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 28580K/32768K available (2562K kernel code, 128K rwdata, 308K rodata, 256K init, 194K bss, 4188K reserved)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:51
Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR842N/ND v2
Switched to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
futex hash table entries: 256 (order: -1, 3072 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 55
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
console [ttyS0] disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
console [ttyS0] enabled
bootconsole [early0] disabled
m25p80 spi0.0: found s25fl064k, expected m25p80
m25p80 spi0.0: s25fl064k (8192 Kbytes)
5 tp-link partitions found on MTD device spi0.0
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x00000012e650 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x00000012e650-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: device 2 (rootfs) set to be root filesystem
1 squashfs-split partitions found on MTD device rootfs
0x000000450000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
libphy: ag71xx_mdio: probed
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
ag71xx-mdio.1: Found an AR934X built-in switch
eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
TCP: cubic registered
NET: Registered protocol family 17
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 256K (80350000 - 80390000)
init: failed to symlink /tmp -> /var
init: Console is alive
init: - watchdog -
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ehci-platform ehci-platform: EHCI Host Controller
ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform: TX-TX IDP fix enabled
ehci-platform ehci-platform: irq 3, io mem 0x1b000000
ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new high-speed USB device number 2 using ehci-platform
init: - preinit -
random: procd urandom read with 9 bits of entropy available
eth1: link up (1000Mbps/Full duplex)
jffs2: notice: (364) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found.
mount_root: switching to jffs2 overlay
eth1: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
NET: Registered protocol family 10
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip6_tables: (C) 2000-2006 Netfilter Core Team
batman_adv: B.A.T.M.A.N. advanced 2014.4.0 (compatibility version 15) loaded
u32 classifier
input device check on
Actions configured
Mirror/redirect action on
netem: version 1.3
Loading modules backported from Linux version master-2015-03-09-0-g141f155
Backport generated by backports.git backports-20150129-0-gdd4a670
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (450 buckets, 1800 max)
xt_time: kernel timezone is -0000
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
usb 1-1: ath9k_htc: Firmware htc_9271.fw requested
usbcore: registered new interface driver ath9k_htc
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
usb 1-1: ath9k_htc: Transferred FW: htc_9271.fw, size: 50980
ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits
ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.3
ath: EEPROM regdomain: 0x809c
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x52
ath: Country alpha2 being used: CN
ath: Regpair used: 0x52
ieee80211 phy1: Atheros AR9271 Rev:1
cfg80211: Calling CRDA for country: CN
cfg80211: Current regulatory domain intersected:
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
device eth1 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): br-batman: link is not ready
eth1: link up (1000Mbps/Full duplex)
br-lan: port 1(eth1) entered forwarding state
br-lan: port 1(eth1) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
eth0: link up (100Mbps/Full duplex)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
br-lan: port 1(eth1) entered forwarding state
IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
device wlan0-1 entered promiscuous mode
random: nonblocking pool is initialized
device wlan0-1 left promiscuous mode
br-batman: port 1(wlan0-1) entered disabled state
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0.12: link is not ready
root@Johannisviertel-Essbar:~#